产品展示
液冷自动排气阀
溶解空气与注入过程夹带的气体会在管路高点积聚形成气堵,导致冷板流量衰减、局部过热与泵气蚀。自动排气阀以浮球为感应元件:腔内积气时液位下降、浮球开启排气口,气体经微孔排气嘴排出;气体排尽后液位回升、浮球复位密封,排气不排液。阀体小巧,滚花外圆便于徒手旋接,垂直安装于系统最高点、CDU 集气腔与分水器顶部,是液冷系统长期稳定运行的“隐形守护件”。
所属分类:
液冷阀门
咨询热线:
液冷自动排气阀
液冷自动排气阀 Automatic Air Vent Valve
莱科液冷自动排气阀,安装于管路高点与分水器顶部,内部浮球随液位自动启闭:有气排气、无气密封,自动排出管路积气消除气堵,保障冷板流量与换热稳定,免人工值守。 The LIKE automatic air vent mounts at line high points and manifold tops. An internal float opens to release accumulated air and seals when liquid returns — removing air pockets automatically to keep cold-plate flow and heat transfer stable, with no manual attention.

| 产品系列 Series | 自动排气阀 Automatic Air Vent Valve |
| 结构型式 Structure | 浮球式自动排气 Float-type auto vent |
| 接口螺纹 Connection | G1/8 / G1/4 / G1/2 内螺纹 |
| 阀体材质 Body | 不锈钢 / 镀镍黄铜 Stainless / nickel-plated brass |
| 工作压力 Working Pressure | 0 ~ 0.6 MPa |
| 典型应用 Typical Use | 管路高点 / CDU 集气腔 / 分水器排气 |
溶解空气与注入过程夹带的气体会在管路高点积聚形成气堵,导致冷板流量衰减、局部过热与泵气蚀。自动排气阀以浮球为感应元件:腔内积气时液位下降、浮球开启排气口,气体经微孔排气嘴排出;气体排尽后液位回升、浮球复位密封,排气不排液。阀体小巧,滚花外圆便于徒手旋接,垂直安装于系统最高点、CDU 集气腔与分水器顶部,是液冷系统长期稳定运行的“隐形守护件”。
Dissolved and entrained air accumulates at high points, forming air pockets that cut cold-plate flow, cause hot spots and pump cavitation. The float-type vent senses liquid level: accumulated air drops the level and opens the micro-orifice to release gas only; once purged, the float reseals. Its compact knurled body screws into system high points, CDU gas chambers and manifold tops for long-term, maintenance-free operation.
| 参数 Parameter | 规格 Specification | |
|---|---|---|
| 接口螺纹 Connection | G1/8 / G1/4 / G1/2 内螺纹 | NPT 可定制 NPT on request |
| 工作压力 Working Pressure | 0 ~ 0.6 MPa | 常压至微正压系统 Ambient to slight positive pressure |
| 工作温度 Temperature Range | 0 ℃ ~ +110 ℃ | 高温工况可选 FKM 密封 FKM seals for higher temperature |
| 适用介质 Media | 去离子水 / 乙二醇水溶液 | 乙二醇浓度 ≤ 50% Glycol up to 50% |
| 排气原理 Principle | 浮球液位差自动启闭 | 排气不排液 Air out, liquid stays in |
| 安装姿态 Orientation | 立式垂直安装 | 排气口朝上 Vent port upright |
| 安装位置 Location | 作用 Purpose | |
|---|---|---|
| 管路高点 Line high points | 排出上行集聚的空气 | 水平管每 15~20 m 及变径处设置 Every 15~20 m and at reducers |
| CDU 集气腔 CDU gas chamber | 排出板换与储液箱积气 | 储液箱顶部预留口安装 Tank-top port |
| 机柜分水器 Manifold top | 排出支路积气 | 分水器顶部预留口 Manifold top port |
| 泵吸入侧 Pump suction | 防止泵气蚀 | 泵前水平段高点 High point before pump |
| 部件 Part | 材质 Material | |
|---|---|---|
| 阀体 Body | 不锈钢 / 黄铜镀镍 | 耐蚀小巧,滚花易旋 Corrosion-resistant, knurled for hand tightening |
| 浮球 Float | 不锈钢空心球 | 灵敏随液位动作 Sensitive to level change |
| 阀座 Seat | EPDM / FKM | 浮球贴合密封,关闭严密 Tight float seating |
| 排气嘴 Vent Orifice | 微孔防喷溅结构 | 只放气不跑液 Air-only discharge |
| 密封圈 O-ring | FKM / EPDM(可选) | 按介质配方选择 Selected per coolant |
| G1/8 | 垂直旋接 Vertical | 分水器顶部、仪表接口 |
| G1/4 / G1/2 | 垂直旋接 Vertical | 管路高点、CDU 集气腔 |
管路高点排气 High-point Venting 自动排除系统最高点积气,维持全流量循环。 Keeps full flow by purging high-point air. | CDU 集气腔 CDU Gas Chamber 板换与储液箱顶部持续排气,保护换热效率。 Continuous venting at tank and exchanger tops. |
机柜分水器排气 Manifold Venting 分水器顶部排气,防止支路因气堵断流。 Prevents branch dead-flow from trapped air. | 储能液冷包 ESS Cooling Loop 电池包液冷回路的积气管理与换热保障。 Air management for battery cooling loops. |
1. 必须垂直安装于管路或设备最高点,排气口朝上;
2. 安装前检查接口螺纹与密封圈,缠绕生料带后旋紧;
3. 首次注液阶段排气频繁属正常现象,待气体排尽后自动进入待机密封状态;
4. 若出现持续渗液,停机检查浮球密封面是否被杂质卡阻;
5. 换液或大修时,可按压浮球手动强制排气。
1. Mount vertically at the highest point, vent port up. 2. Check thread and O-ring; seal with PTFE tape and tighten. 3. Frequent venting during first fill is normal; the float then holds sealed standby. 4. If it weeps continuously, inspect the float seat for debris. 5. Press the float to force-vent during refill or overhaul.
订货时请注明:接口螺纹规格(G1/8 ~ G1/2)· 阀体材质(不锈钢 / 镀镍黄铜)· 密封材料(FKM / EPDM)· 是否需要手动帽。可按项目需求提供批量配套。
When ordering, please specify: thread size (G1/8~G1/2), body material (stainless / plated brass), seal material (FKM / EPDM) and whether a manual cap is needed. Bulk supply available for projects.
上一页
液冷注液阀、排液阀
下一页




津公网安备 12011602000999号