产品展示
液冷注液阀、排液阀
注液阀与排液阀是液冷系统全生命周期的“进液口”与“出液口”:系统初次注液、运行补液、换液放空、检修排污都经由这两只小阀完成。莱科采用迷你球阀结构,全通径球体流阻低、加注速度快;90° 手柄带开度定位,开关状态一目了然;接口端可选快插、卡箍或宝塔软管端,与加注车、放液软管快速对接。阀体 304 / 316L 不锈钢,内腔抛光,适配去离子水、乙二醇与氟化液,安装于 CDU 储液箱、机柜分水器与管路最低点。
所属分类:
液冷阀门
咨询热线:
液冷注液阀、排液阀
液冷注液阀、排液阀 Liquid Cooling Fill & Drain Valve
莱科液冷注液阀、排液阀,设于 CDU 与机柜补液口 / 排污口的手动球阀,蓝色 90° 手柄开关到位清晰,快插 / 卡箍端直连加注软管,注液、补液、放空、排污一步完成。 The LIKE fill & drain valve is a compact manual ball valve for CDU and cabinet make-up / drain ports. A position-coded blue lever and quick-fit or clamp ends connect directly to filling hoses — filling, topping-up, venting and draining in one step.

| 产品系列 Series | 液冷注液阀、排液阀 Fill & Drain Valve |
| 结构型式 Structure | 手动迷你球阀 Mini manual ball valve |
| 公称通径 Bore | DN8 / DN10 / DN15(1/4″ ~ 1/2″) |
| 阀体材质 Body | CF8(304)/ CF8M(316L)不锈钢 |
| 连接方式 Connection | 快插端 / 卡箍端 / 软管宝塔端(可组合) |
| 典型应用 Typical Use | CDU 补液口 / 机柜注排液 / 系统放空排污 |
注液阀与排液阀是液冷系统全生命周期的“进液口”与“出液口”:系统初次注液、运行补液、换液放空、检修排污都经由这两只小阀完成。莱科采用迷你球阀结构,全通径球体流阻低、加注速度快;90° 手柄带开度定位,开关状态一目了然;接口端可选快插、卡箍或宝塔软管端,与加注车、放液软管快速对接。阀体 304 / 316L 不锈钢,内腔抛光,适配去离子水、乙二醇与氟化液,安装于 CDU 储液箱、机柜分水器与管路最低点。
Fill and drain valves are the make-up and discharge points of a liquid cooling system throughout its life: initial filling, top-up, coolant change-out and drain-down all pass through them. The LIKE mini ball valve offers full-bore flow for fast filling, a position-coded 90° lever for at-a-glance status, and quick-fit, clamp or hose-barb ends that dock directly with filling carts. The polished 304 / 316L body suits DI water, glycol and dielectric fluids.
| 参数 Parameter | 规格 Specification | |
|---|---|---|
| 通径范围 Size Range | DN8 / DN10 / DN15 | 小口径微量加注与排放 For metered filling |
| 工作压力 Working Pressure | 0 ~ 1.0 MPa | — |
| 工作温度 Temperature Range | -10 ℃ ~ +150 ℃ | 取决于密封材料 Depends on seal selection |
| 适用介质 Media | 去离子水 / 乙二醇水溶液 / 氟化液 | 兼容主流冷却工质 Mainstream coolants |
| 操作方式 Operation | 手动手柄 90° 开关 | 开关位置一目了然 Position-coded lever |
| 密封 Seals | PTFE 阀座 + FKM / EPDM O 圈 | 按介质选择 Selected per coolant |
| 配置 Configuration | 功能 Function | |
|---|---|---|
| 注液阀 Fill Valve | 系统初次加注与日常补液接口 | CDU 储液箱上部 / 机柜顶部 Top of tank or cabinet |
| 排液阀 Drain Valve | 换液、检修时放空与排污 | 系统最低点 / 集水箱底部 Lowest point / tank bottom |
| 放空配合 Vent Assist | 注液时配合排气口排除腔内空气 | 管路高点配合使用 With high-point vents |
| 部件 Part | 材质 Material | |
|---|---|---|
| 阀体 Body | CF8(304)/ CF8M(316L) | 迷你阀体,紧凑轻量 Compact, lightweight |
| 球体 Ball | 不锈钢抛光全通径 | 全通径低流阻,加注快 Full bore for fast filling |
| 阀座 Seat | PTFE(聚四氟乙烯) | 自润滑低扭矩 Self-lubricating, low torque |
| 手柄 Handle | 蓝色包胶 T 型手柄 | 开度定位,防滑到位 Position-coded, anti-slip |
| 接口端 Ends | 快插 / 卡箍 / 宝塔软管端 | 与加注软管快速对接 Docks with filling hoses |
| DN8 / DN10 | 宝塔软管端 Hose barb | φ6 / φ8 / φ10 PVC 软管 |
| DN8 / DN10 | 快插端 Push-fit | φ6 / φ8 / φ10 软管快插 |
| DN15 / 1/2″ | 卡箍端 Clamp | 不锈钢管 + 卡箍接头 |
CDU 补液口 CDU Make-up Port 储液箱液位下降后的日常补液操作口。 Daily top-up port for the CDU tank. | 机柜注排液 Cabinet Fill & Drain 服务器机柜二次侧注液与换液放空。 Secondary-loop filling and change-out for cabinets. |
换液排污 Coolant Change-out 按维护周期放空旧液、冲洗、重注新液。 Drain, flush and refill on maintenance cycles. | 测试台加注 Test Bench Filling 液冷测试台快速加注与排空接口。 Fast fill / empty ports for test benches. |
1. 注液阀设于系统高点或储液箱顶部,排液阀设于系统最低点,保证排空彻底;
2. 快插端插入软管前将管口剪平,插入到位后轻拉确认锁紧;
3. 加注时先开注液阀、配合排气阀排气,液位到位后关闭;
4. 冬季运输或长期停机前,通过排液阀将系统内液体排空;
5. 每季度全行程操作数次,防止阀杆卡滞。
1. Locate fill valves at the highest point or tank top, drain valves at the lowest point. 2. Cut hose ends squarely before push-fit insertion; tug to confirm lock. 3. When filling, open the fill valve with vents assisted, then close at level. 4. Drain the system via the drain valve before winter transport or long shutdown. 5. Cycle quarterly to keep the stem free.
订货时请注明:通径规格(DN8 ~ DN15)· 接口端形式(快插 / 卡箍 / 宝塔端,可组合)· 阀体材质(304 / 316L)· 密封材料(FKM / EPDM)· 手柄颜色与介质。可按项目需求提供批量配套与定制刻字。
When ordering, please specify: size (DN8~DN15), end type (push-fit / clamp / barb, combinable), body material (304 / 316L), seal material (FKM / EPDM), lever color and media. Bulk supply and custom marking available for projects.
上一页
卡箍止回阀
下一页




津公网安备 12011602000999号