产品展示
卡箍止回阀
卡箍止回阀是洁净液冷管路的防回流阀门。阀瓣由弹簧预紧,介质正向流动时克服弹簧力开启、压降小;停泵或发生回流时阀瓣瞬时复位关闭,抑制倒流与水锤。阀体、阀瓣均采用不锈钢,内腔流道抛光、无卫生死角;两端卡箍快装结构无需动火与专用工具,拆开阀盖即可更换阀瓣与弹簧,特别适合去离子水、乙二醇等高洁净度要求的液冷回路,常与泵出口、冷板支路串联安装。
所属分类:
液冷阀门
咨询热线:
卡箍止回阀
卡箍止回阀 Sanitary Clamp Check Valve
莱科卡箍止回阀(卫生级洁净止回阀),快装卡箍连接,弹簧加载阀瓣随流自动开启、停泵回流瞬时关闭,流道抛光无死角,拆装清洗便捷,用于洁净液冷回路的防回流保护。 The LIKE sanitary clamp check valve uses a spring-loaded disc that opens with flow and snaps shut on reversal. Clamp quick-fit ends and a polished, dead-leg-free bore make it ideal for back-flow protection in high-cleanliness liquid cooling loops.

| 产品系列 Series | 卡箍止回阀 Sanitary Clamp Check Valve |
| 结构型式 Structure | 弹簧提升瓣式 Spring-loaded lift disc |
| 公称通径 Bore | DN15 ~ DN50(1/2″ ~ 2″) |
| 阀体材质 Body | CF8(304)/ CF8M(316L)不锈钢 |
| 连接方式 Connection | 卡箍快装 Clamp(可定制焊接 / 螺纹端) |
| 典型应用 Typical Use | 洁净液冷回路防回流 / 泵出口保护 |
卡箍止回阀是洁净液冷管路的防回流阀门。阀瓣由弹簧预紧,介质正向流动时克服弹簧力开启、压降小;停泵或发生回流时阀瓣瞬时复位关闭,抑制倒流与水锤。阀体、阀瓣均采用不锈钢,内腔流道抛光、无卫生死角;两端卡箍快装结构无需动火与专用工具,拆开阀盖即可更换阀瓣与弹簧,特别适合去离子水、乙二醇等高洁净度要求的液冷回路,常与泵出口、冷板支路串联安装。
The sanitary clamp check valve is a back-flow prevention valve for high-cleanliness liquid cooling lines. A spring-preloaded disc opens against flow with low pressure drop and resets instantly on pump stop or flow reversal, curbing back-flow and water hammer. Stainless body and disc with a polished, pocket-free bore suit deionized water and glycol service, while clamp ends allow tool-free removal of the cover for disc or spring replacement in minutes.
| 参数 Parameter | 规格 Specification | |
|---|---|---|
| 通径范围 Size Range | DN15 / DN20 / DN25 / DN32 / DN40 / DN50 | 其他口径可定制 Other sizes on request |
| 结构型式 Type | 弹簧提升瓣式止回阀 Spring lift check | 水平 / 垂直管路均可安装 Fits horizontal & vertical lines |
| 开启压差 Cracking Pressure | ≤ 0.03 MPa | 低开启压差,泵功耗影响小 Negligible pump penalty |
| 工作压力 Working Pressure | 0 ~ 1.0 MPa | 更高压力工况请联系选型 For higher pressure, contact us |
| 工作温度 Temperature Range | -10 ℃ ~ +150 ℃ | 取决于密封材料选型 Depends on seal selection |
| 适用介质 Media | 去离子水 / 乙二醇水溶液 / 合成冷却液 | Deionized water, glycol solution, synthetic coolant |
| 项目 Item | 说明 Description | |
|---|---|---|
| 弹簧提升瓣式 Spring lift disc | 阀瓣带弹簧预紧,任意安装姿态可靠关闭 | 泵出口、高位回路首选 Standard for pump outlets and high points |
| 全流量流道 Full bore | 流道与接管通径一致,流阻低 | 支路压降敏感工况选全流量 Choose full bore where pressure drop matters |
| 抛光内腔 Polished bore | 内腔 Ra ≤ 0.8 μm,可定制电解抛光 | 高洁净与半导体场合推荐 Recommended for semiconductor-grade cleanliness |
| 部件 Part | 材质 Material | |
|---|---|---|
| 阀体 Body | CF8(304)/ CF8M(316L) | 精密铸造,内外抛光 Precision casting, polished inside & out |
| 阀瓣 Disc | 不锈钢锥面瓣 + FKM 密封圈 | 锥面密封,关闭严密 Conical seat, tight shut-off |
| 弹簧 Spring | 304 / 316L 不锈钢 | 耐蚀恒力,快速复位 Corrosion-resistant, instant reset |
| 密封圈 Seals | FKM / EPDM / PTFE(可选) | 按介质与温度选择 Selected per coolant & temperature |
| 卡箍端 Ferrule | 标准快装卡箍端 Clamp ends | 适配 ISO 2852 卡箍尺寸 Fits standard clamp dimensions |
| DN15 / 1/2″ ~ DN25 / 1″ | 卡箍快装 Clamp | ISO 2852 · 50.5 外径系列 | 软管 / 不锈钢管 + 卡箍接头 |
| DN32 / 1-1/4″ ~ DN50 / 2″ | 卡箍快装 Clamp | ISO 2852 · 77 ~ 91 外径系列 | 不锈钢管 + 卡箍接头 |
CDU 泵出口防回流 Pump Outlet Protection 安装在循环泵出口,防止停泵时冷却液倒流冲击泵体。 Prevents back-flow to the pump at shutdown. | 冷板支路隔离 Branch Isolation 冷板支路串联止回,避免相邻支路串流、短路循环。 Stops cross-flow between parallel cold-plate branches. |
半导体洁净冷却回路 Semiconductor Cooling 抛光洁净流道,适配半导体设备高纯度冷却液回路。 Polished bore for high-purity coolant circuits. | 储能与功率器件液冷 Energy Storage & Power Electronics 储能 PCS 与功率模块冷却回路的防回流保护。 Back-flow protection in PCS and power module loops. |
1. 按阀体箭头方向安装,箭头指向为允许流动方向,不得反装;
2. 卡箍端配装密封垫圈后锁紧卡箍,确认两端到位无歪斜;
3. 首次运行时观察泵启停过程,确认阀瓣启闭正常、无异常噪声;
4. 检修时泄压后拆开卡箍即可取出阀瓣与弹簧,复装更换密封垫圈;
5. 长期停机后建议全流路冲洗并检查阀瓣动作灵活。
1. Install with the flow arrow; never reverse. 2. Fit gaskets and lock the clamp couplings squarely. 3. On first run, verify disc travel and quiet operation at pump start / stop. 4. For service, depressurize, open the clamp and lift out disc and spring; renew gaskets on reassembly. 5. After long shutdowns, flush the line and check disc mobility.
订货时请注明:通径规格(DN15 ~ DN50)· 阀体材质(304 / 316L)· 连接方式(卡箍 / 对焊 / 承插焊 / 螺纹)· 密封材料(FKM / EPDM)· 开启压差要求与介质。可按项目需求提供批量配套与定制刻字。
When ordering, please specify: size (DN15~DN50), body material (304 / 316L), end connection (clamp / BW / SW / thread), seal material (FKM / EPDM), required cracking pressure and media. Bulk supply and custom laser marking are available for projects.
上一页
弹簧静音止回阀
下一页




津公网安备 12011602000999号