产品展示
弹簧静音止回阀
液冷系统泵组停机时,管路中介质的惯性回流会在止回阀处产生猛烈关闭与压力冲击,即「水锤」,轻则噪声扰人,重则击穿管路附件、损坏泵体。莱科弹簧静音止回阀内置不锈钢弹簧,阀瓣在流量衰减、回流尚未建立的瞬间即被弹簧推回密封位,把关闭行程化解在低流速区,从根本上抑制水锤与关阀噪声。对夹式短结构面距短、重量轻,可直接夹装在两法兰之间;开启压差低,泵功耗几乎不受影响。全不锈钢材质适配去离子水与乙二醇冷却液,是液冷泵出口、变频泵回路与多泵并联系统防回流、抗水锤的标配阀门。
所属分类:
液冷阀门
咨询热线:
弹簧静音止回阀
弹簧静音止回阀 Spring Silent Check Valve
莱科弹簧静音止回阀,弹簧辅助阀瓣在停泵瞬间提前关闭,防止介质回流并抑制水锤噪声,液冷泵出口的标配防护阀门,保护泵组与管路安全。 The LIKE spring silent check valve closes at pump stop before reverse flow builds, preventing backflow and suppressing water-hammer noise — the standard pump-discharge protection valve for liquid cooling loops.

| 产品系列 Series | 弹簧静音止回阀 Spring Silent Check Valve |
| 公称通径 Bore | DN15 ~ DN200(1/2″ ~ 8″) |
| 结构形式 Structure | 对夹式短结构,弹簧辅助关闭 |
| 阀体材质 Body | CF8(304)/ CF8M(316L)不锈钢 |
| 安装姿态 Orientation | 水平 / 垂直均可 |
| 典型应用 Typical Use | 液冷泵出口 / 支路防回流 |
液冷系统泵组停机时,管路中介质的惯性回流会在止回阀处产生猛烈关闭与压力冲击,即「水锤」,轻则噪声扰人,重则击穿管路附件、损坏泵体。莱科弹簧静音止回阀内置不锈钢弹簧,阀瓣在流量衰减、回流尚未建立的瞬间即被弹簧推回密封位,把关闭行程化解在低流速区,从根本上抑制水锤与关阀噪声。对夹式短结构面距短、重量轻,可直接夹装在两法兰之间;开启压差低,泵功耗几乎不受影响。全不锈钢材质适配去离子水与乙二醇冷却液,是液冷泵出口、变频泵回路与多泵并联系统防回流、抗水锤的标配阀门。
When cooling pumps stop, inertial reverse flow slams ordinary check valves shut, causing water hammer — noise at best, damaged piping and pumps at worst. The LIKE spring silent check valve uses an internal stainless spring to seat the disc the moment flow decays, before reverse flow develops, dissolving the closing stroke at low velocity and eliminating slam and noise. The short wafer body clamps between flanges with minimal face-to-face length and weight, while low cracking pressure keeps pump power unaffected. All-stainless construction suits DI water and glycol coolants — the standard anti-backflow, anti-hammer valve for pump discharge, VFD loops and multi-pump manifolds.
| 参数 Parameter | 规格 Specification | 说明 Remarks |
|---|---|---|
| 通径范围 Size Range | DN15 ~ DN200(1/2″ ~ 8″) | 其他口径可定制 Other sizes on request |
| 结构形式 Structure | 对夹式短结构,弹簧辅助关闭 | 面距短、重量轻 Short face-to-face, light |
| 开启压差 Cracking Pressure | ≤ 3 kPa(按通径) | 低阻损低泵耗 Low loss, low pump power |
| 关闭方式 Closing | 弹簧先关 + 介质压差密封 | 回流建立前即关闭 Closes before reverse flow |
| 阀体材质 Body | CF8(304)/ CF8M(316L) | 不锈钢铸造耐蚀 Corrosion-resistant casting |
| 工作压力 Working Pressure | 0 ~ 1.6 MPa | 更高压力工况请联系选型 For higher pressure, contact us |
| 工作温度 Temperature Range | -10 ℃ ~ +120 ℃ | 取决于密封材料 Depends on seal selection |
| 适用介质 Media | 去离子水 / 乙二醇水溶液 / 合成冷却液 | Deionized water, glycol solution, coolant |
| 型式 Type | 关闭特性 Closing Trait | 典型用途 Typical Duty |
|---|---|---|
| 弹簧静音式 Spring Silent | 弹簧先关,回流前闭合,无水锤噪声 | 泵出口与变频泵回路 Pump discharge, VFD loops |
| 旋启式 Swing | 靠回流关闭,动作慢易水锤 | 对噪声不敏感的大口径场合 Noise-insensitive large bores |
| 球式 / 活塞式 Ball / Piston | 结构简单,关闭速度一般 | 辅助管路与排污回路 Auxiliary and drain lines |
| 部件 Part | 材质 Material | 特性 Feature |
|---|---|---|
| 阀体 Body | CF8(304)/ CF8M(316L) | 精密铸造,对夹短结构 Precision casting, short wafer body |
| 阀瓣 Disc | 不锈钢阀瓣 + 弹簧组件 | 弹簧先关,回流前闭合 Spring-assisted pre-reverse closure |
| 弹簧 Spring | 不锈钢弹簧 | 耐疲劳,动作寿命长 Fatigue-resistant long life |
| 阀座 Seat | PTFE / 不锈钢堆焊 | 密封可靠,双向承压 Tight bidirectional sealing |
| 导向套 Guide | 不锈钢精密导向 | 阀瓣运动平稳,无偏磨 Stable disc travel, no side wear |
| 密封圈 O-ring | FKM / EPDM(可选) | 按介质配方选择 Selected per coolant formulation |
| 规格 Size | 弹簧组件 Spring | 连接方式 End Connection | 适配管路 Matching Pipe |
|---|---|---|---|
| DN15 / 1/2″ ~ DN50 / 2″ | 不锈钢弹簧阀瓣 | 对夹式 Wafer / 螺纹 / 卡箍 | 不锈钢管 + 对应接头 |
| DN65 / 2-1/2″ ~ DN200 / 8″ | 不锈钢弹簧阀瓣 | 对夹式 Wafer | 管道法兰 + 双头螺栓 |
液冷泵出口保护 Pump Discharge Protection 泵出口标配,停泵防回流、防水锤。Standard at pump discharge against backflow and water hammer. | 多泵并联系统 Multi-pump Manifolds 并联泵组间防止倒灌与环流。Prevents back-feeding and circulating flow between parallel pumps. |
变频泵回路 VFD Pump Loops 变频频繁启停工况的静音防回流。Silent anti-backflow under frequent VFD start-stops. | 支路防回流 Branch Backflow Prevention 支路接入点的防回流隔离,保护冷板。Backflow isolation at branch tie-ins protecting cold plates. |
1. 安装时流向与阀体箭头一致,优先安装在泵出口后 5 倍管径以内的直管段;
2. 对夹安装时蝶板全开方向与法兰间距匹配,均匀对称紧固;
3. 垂直管路安装时确认介质流向为自下而上(升降式结构);
4. 系统试压时注意止回阀单向承压特性,反向不做强度考核;
5. 定期检查弹簧回位与密封面状态,泵检修时一并检查阀瓣。
1. Follow the flow arrow, ideally within 5 pipe diameters of the pump discharge. 2. For wafer installation, match the disc swing to the flange spacing and torque evenly. 3. On vertical runs confirm upward flow for lift-type trims. 4. During pressure testing, note the valve is pressure-rated one-way only. 5. Periodically check spring return and sealing faces; inspect the disc during pump service.
订货时请注明:通径规格(DN15 ~ DN200)· 连接方式(对夹 / 螺纹 / 卡箍 / 法兰)· 阀体材质(304 / 316L)· 开启压差要求· 工作压力与介质· 安装姿态。可按泵组参数推荐规格。
When ordering, please specify: size (DN15~DN200), end connection (wafer / thread / clamp / flange), body material (304 / 316L), cracking pressure requirement, working pressure and media, and installation orientation. Sizing advice available per pump data.
上一页
电动/气动液冷蝶阀
下一页


津公网安备 12011602000999号