产品展示
CDU集成阀组
CDU 机柜内的阀件数量多、接口密,现场逐件配管耗时长、泄漏点多。莱科 CDU 集成阀组把切断、过滤、排气、调压、泄压等功能模块按工艺流程预集成在撬装底座上:管路采用 304 / 316L 卫生级管,工厂内完成装配、1.5 倍压力保压测试与清洗吹扫,测试报告随货交付;到场后仅需对接进出总管与测点线缆,即可投入调试。各功能模块独立可拆,单点检修不影响整体;预留温度压力测点与传感器接口,方便对接 DCIM 监控,是液冷集成商缩短交付周期的成套方案。
所属分类:
液冷阀门
咨询热线:
CDU集成阀组
CDU集成阀组 CDU Manifold Assembly
莱科 CDU 集成阀组,将切断球阀、过滤器、排气阀、泄压 / 稳压阀按工艺流程集成于模块化撬装底座,出厂前整体装配并打压测试,到场即接即用,大幅压缩集成商现场配管与调试工时。 The LIKE CDU manifold assembly integrates shut-off ball valves, strainers, air vents and relief / stabilizing valves onto a modular skid, assembled and pressure-tested as a unit before delivery. It hooks up on arrival — slashing integrators’ on-site piping and commissioning hours.

| 产品系列 Series | CDU集成阀组 CDU Manifold Assembly |
| 集成功能 Functions | 切断 / 过滤 / 排气 / 调压 / 泄压 |
| 模块通径 Bore | DN25 ~ DN100(按流量配置) |
| 主体材质 Materials | 304 / 316L 不锈钢管路 + 阀件 |
| 交付状态 Delivery | 整体装配 · 打压测试 · 清洗吹扫 |
| 典型应用 Typical Use | CDU 主机 / 集分水器 / 二级冷却分配 |
CDU 机柜内的阀件数量多、接口密,现场逐件配管耗时长、泄漏点多。莱科 CDU 集成阀组把切断、过滤、排气、调压、泄压等功能模块按工艺流程预集成在撬装底座上:管路采用 304 / 316L 卫生级管,工厂内完成装配、1.5 倍压力保压测试与清洗吹扫,测试报告随货交付;到场后仅需对接进出总管与测点线缆,即可投入调试。各功能模块独立可拆,单点检修不影响整体;预留温度压力测点与传感器接口,方便对接 DCIM 监控,是液冷集成商缩短交付周期的成套方案。
A CDU cabinet involves many valves and joints, so field piping is slow and leak-prone. The LIKE manifold assembly pre-integrates shut-off, filtration, venting, pressure regulation and relief modules on a skid: 304 / 316L sanitary piping is assembled, 1.5× pressure-tested and flushed in the factory with reports supplied. On site, only mains and sensor wiring hook up before commissioning. Each module is independently removable for service, with temperature / pressure ports ready for DCIM — a complete package that shortens delivery schedules.
| 参数 Parameter | 规格 Specification | |
|---|---|---|
| 集成模块 Modules | 球阀 / Y 型过滤器 / 排气阀 / 稳压阀 / 泄压阀 / 止回阀 | 按工艺增减 Configurable per process |
| 通径范围 Size Range | DN25 ~ DN100 | 按 CDU 流量选配 Sized per CDU flow |
| 设计压力 Design Pressure | 0 ~ 1.0 MPa | 更高压力可定制 Higher on request |
| 适用介质 Media | 去离子水 / 乙二醇水溶液 / 氟化液 | Deionized water, glycol, dielectric fluid |
| 接口形式 Connections | 法兰 / 卡箍 / 螺纹(可组合) | 与 CDU 预留口对接 Matches CDU ports |
| 出厂测试 Factory Test | 1.5 倍压力保压测试 + 冲洗记录 | 测试报告随货 Reports with delivery |
| 模块 Module | 元件 Components | |
|---|---|---|
| 切断模块 Shut-off | 手动 / 电动球阀 | 主回路启停与检修隔离 Loop start-stop and isolation |
| 净化模块 Filtration | Y 型过滤器 + 排气阀 | 拦截杂质、排除积气 Trap debris, purge air |
| 压力模块 Pressure | 稳压阀 + 安全泄压阀 | 定压运行与超压保护 Regulation and overpressure relief |
| 分配模块 Distribution | 集分水器 + 温度 / 压力测点 | 多支路分配与运行监测 Branch distribution and monitoring |
| 部件 Part | 材质 Material | |
|---|---|---|
| 管路 Piping | 304 / 316L 卫生级不锈钢管 | 内壁处理,低析出 Treated bore, low leach |
| 阀件 Valves | 莱科液冷系列阀门 | 同厂配套,接口一致 Matched LIKE valves, uniform ports |
| 底座 Skid | 铝合金 / 碳钢喷塑撬座 | 模块化布局,吊装就位 Modular, lifting-ready |
| 测点 Instrument Ports | 压力表 / 温度计 / 传感器接口 | 预留 DCIM 对接 Ready for DCIM |
| 密封 Seals | FKM / EPDM | 按介质配方统一选择 Selected per coolant |
| 进出总管 Main inlet / outlet | 法兰 / 卡箍 / 螺纹 | 口径与方位按 CDU 预留口定制 Sized to CDU ports |
| 排污与泄放口 Drain / relief | 螺纹接口 | 集中引排至接液盘 Piped to a drain tray |
| 测点接口 Instrument ports | G1/4 内螺纹 | 对接传感器与二次仪表 For sensors and secondary instruments |
CDU 主机配套 CDU Integration 冷量分配单元内部的成套流体控制模块。 Complete fluid-control package inside CDUs. | 集分水器模块 Manifold Module 多支路分配、隔离与监测一体化交付。 Integrated branch distribution, isolation and monitoring. |
二级冷却分配 Secondary Distribution 楼层或列间二级分配单元的阀组配套。 Valve package for row / floor secondary units. | 储能液冷撬装 ESS Skid 储能项目的撬装化液冷阀组方案。 Skid-mounted valve package for ESS projects. |
1. 到货核对出厂测试报告与接口方位图,按流向箭头确认进出总管;
2. 撬装底座吊装就位、调平后固定,再对接进出管与测点线缆;
3. 接入系统前复做一次整体气密检查,确认运输无松动;
4. 运行首周观察各测点读数与模块阀位,纳入日常点检;
5. 备用支路阀位保持全开,检修模块时先切旁路再拆卸。
1. Check the factory test report and port orientation drawing; confirm mains per flow arrows. 2. Land and level the skid, then connect mains and instrument wiring. 3. Re-verify overall tightness before tying in, in case of transit loosening. 4. During the first week, log instrument readings and valve positions into routine checks. 5. Keep standby branches open; switch to bypass before removing any module.
订货时请注明:CDU 流量与通径(DN25 ~ DN100)· 所需功能模块清单· 接口形式与方位(可提供图纸)· 材质等级(304 / 316L)· 是否需要测点与自控对接。支持非标定制与项目成套交付。
When ordering, please specify: CDU flow and size (DN25~DN100), module list, port types and orientations (drawings welcome), material grade (304 / 316L) and instrument / control requirements. Non-standard and project packages supported.
上一页
液冷Y型过滤器
下一页




津公网安备 12011602000999号