产品展示
液冷Y型过滤器
冷板微通道当量直径不足 1 mm,一次调试残留的焊渣或冷却系统析出的颗粒就足以造成不可逆堵塞。Y 型过滤器安装在冷板与精密阀件上游:Y 形斜仓内置冲孔 + 编织复合滤网,流道直通、压降低,过滤面积达通径截面积 3 倍以上,清洗周期长;滤仓朝下或朝侧安装,杂质沉降在滤仓内,旋开排污堵头即可在线排污,卸开卡箍即可抽出滤网清洗。CF8M 不锈钢阀体耐乙二醇与缓蚀剂长期浸泡,是洁净液冷回路的标准前置保护件。
所属分类:
液冷阀门
咨询热线:
液冷Y型过滤器
液冷Y型过滤器 Y-Strainer
莱科 Y 型过滤器,Y 形流道内置不锈钢滤网,拦截冷却液中的颗粒、焊渣与析出物,保护冷板微通道与精密阀件免于堵塞;卡箍快装端拆卸滤网清洗便捷,目数按冷板要求选配。 The LIKE Y-strainer holds a stainless mesh screen in a Y-shaped body, trapping particles, weld slag and precipitates before they reach cold-plate microchannels and precision valves. Clamp ends make screen removal and cleaning quick; mesh is selected per cold-plate requirements.

| 产品系列 Series | Y 型过滤器 Y-Strainer |
| 公称通径 Bore | DN15 ~ DN50(1/2″ ~ 2″) |
| 滤网 Screen | 304 不锈钢 20 ~ 100 目可选 |
| 阀体材质 Body | CF8M(316L)不锈钢 |
| 连接方式 Connection | 卡箍快装(可定制螺纹 / 法兰) |
| 典型应用 Typical Use | 冷板前置过滤 / CDU 泵前过滤 |
冷板微通道当量直径不足 1 mm,一次调试残留的焊渣或冷却系统析出的颗粒就足以造成不可逆堵塞。Y 型过滤器安装在冷板与精密阀件上游:Y 形斜仓内置冲孔 + 编织复合滤网,流道直通、压降低,过滤面积达通径截面积 3 倍以上,清洗周期长;滤仓朝下或朝侧安装,杂质沉降在滤仓内,旋开排污堵头即可在线排污,卸开卡箍即可抽出滤网清洗。CF8M 不锈钢阀体耐乙二醇与缓蚀剂长期浸泡,是洁净液冷回路的标准前置保护件。
Cold-plate microchannels are under 1 mm across — a single weld bead or precipitated particle can plug them for good. Mounted upstream of cold plates and precision valves, the Y-strainer combines a perforated-plus-woven stainless screen with a straight-through low-loss body; screen area is over 3× the bore area for long cleaning intervals. Mounted screen-chamber down or sideways, debris settles into the bowl: blow down via the plug in service, or open the clamp to lift the screen. The CF8M body withstands glycol and inhibitor blends long-term.
| 参数 Parameter | 规格 Specification | |
|---|---|---|
| 通径范围 Size Range | DN15 ~ DN50 | — |
| 滤网规格 Screen Mesh | 20 / 40 / 60 / 80 / 100 目 | 冷板回路建议 ≥ 60 目 ≥60 mesh for cold plates |
| 过滤面积 Screen Area | 通径截面积 3 倍以上 | 清洗周期长 Long cleaning interval |
| 工作压力 Working Pressure | 0 ~ 1.0 MPa | — |
| 工作温度 Temperature Range | -10 ℃ ~ +150 ℃ | — |
| 排污方式 Drainage | 底部排污堵头(标配) | 可改装排污阀 Drain valve retrofit available |
| 目数 Mesh | 过滤精度 Rating | |
|---|---|---|
| 20 ~ 40 目 | 850 ~ 400 μm | 泵前粗过滤、新装管路调试期 Pump pre-filtration, commissioning |
| 60 ~ 80 目 | 250 ~ 180 μm | 常规冷板回路 Standard cold-plate loops |
| 100 目 | 150 μm | 微通道冷板精密过滤 Microchannel precision filtration |
| 部件 Part | 材质 Material | |
|---|---|---|
| 阀体 Body | CF8M(316L)精密铸造 | 耐乙二醇与缓蚀剂长期浸泡 Resists glycol and inhibitors |
| 滤网 Screen | 304 冲孔板 + 编织网复合 | 双层结构强度与精度兼顾 Strength plus fineness |
| 密封 Seals | EPDM / FKM / PTFE | 按介质与温度选择 Selected per coolant & temperature |
| 排污堵头 Drain Plug | 不锈钢六角堵头 | 在线排污快捷 In-line blow-down |
| 卡箍端 Clamp Ends | 标准快装卡箍端 | 卸开即抽滤网 Screen lifts out in minutes |
| DN15 / 1/2″ ~ DN25 / 1″ | 卡箍快装 Clamp | 不锈钢管 + 卡箍接头 |
| DN32 ~ DN50 | 卡箍快装 / 法兰 Clamp / flange | 不锈钢管 + 卡箍接头 |
冷板前置保护 Cold-plate Protection 微通道冷板入口的最后屏障,防堵塞于未然。 Final barrier before microchannel cold plates. | CDU 泵前过滤 Pump Inlet Straining 拦截回流管路带入的颗粒,保护循环泵。 Shields the pump from return-line debris. |
调试期焊渣拦截 Commissioning Straining 新装管路调试期拦截焊渣与施工杂物。 Catches weld slag and debris at commissioning. | 分水器支路过滤 Branch Filtration 各支路独立过滤,便于定位杂质来源。 Per-branch straining helps trace debris sources. |
1. 按阀体箭头方向安装,滤仓朝下或朝侧,禁止滤仓朝上;
2. 卡箍端配装密封垫圈后锁紧,调试期建议每周检查一次滤网;
3. 观察过滤器前后压差或冷板流量,明显增大时及时清洗;
4. 排污时缓慢旋开堵头,防止带压介质喷溅;
5. 清洗滤网用软毛刷与清水,禁用钢丝刷,复装更换密封垫。
1. Install with the flow arrow, chamber down or sideways — never up. 2. Fit gaskets and lock clamps; inspect the screen weekly during commissioning. 3. Clean when differential pressure rises or cold-plate flow drops. 4. Open the drain plug slowly to avoid spray. 5. Brush the screen with a soft brush and water only; renew gaskets on reassembly.
订货时请注明:通径规格(DN15 ~ DN50)· 滤网目数(20 ~ 100 目)· 阀体材质(304 / 316L)· 连接方式(卡箍 / 螺纹 / 法兰)· 是否需要排污阀。可按项目需求提供批量配套。
When ordering, please specify: size (DN15~DN50), mesh (20~100), body material (304 / 316L), end connection (clamp / thread / flange) and whether a drain valve is needed. Bulk supply available.
上一页
液冷稳压阀
下一页




津公网安备 12011602000999号