产品展示
液冷安全泄压阀
液冷回路中的循环泵憋压、换热器堵塞或阀门误关都会造成压力爬升,超出冷板与管路的承压极限即引发泄漏。安全泄压阀是被保护系统的最后一道防线:弹簧直接载荷式结构,进口压力达到整定值即克服弹簧力开启,过压介质经泄放口排出;压力回落后阀瓣自动回座关闭,最大限度减少冷却液损失。整定压力按订单出厂标定并铅封,现场免调试;阀体铸出流向箭头与整定参数,安装核对直观,广泛用于 CDU 主回路、泵出口与冷板入口保护。
所属分类:
液冷阀门
咨询热线:
液冷安全泄压阀
液冷安全泄压阀 Safety Relief Valve
莱科液冷安全泄压阀,系统压力超过整定值自动开启泄放,压力回落自动关闭复位,全程无需人工干预;黄铜 / 不锈钢阀体,出厂整定并铅封,保护冷板、CDU 与管路免受超压损害。 The LIKE safety relief valve opens automatically at set pressure, discharges the excess and reseats when pressure falls back — no operator action needed. Brass or stainless body, factory set and lead-sealed, protects cold plates, CDUs and piping from overpressure.

| 产品系列 Series | 安全泄压阀 Safety Relief Valve |
| 整定压力 Set Pressure | 0.2 ~ 1.0 MPa(可定制) |
| 公称通径 Bore | DN8 ~ DN25 |
| 阀体材质 Body | 黄铜 / 不锈钢(可选) |
| 连接方式 Connection | G / NPT 内螺纹 |
| 典型应用 Typical Use | CDU 回路 / 冷板入口 / 泵出口保护 |
液冷回路中的循环泵憋压、换热器堵塞或阀门误关都会造成压力爬升,超出冷板与管路的承压极限即引发泄漏。安全泄压阀是被保护系统的最后一道防线:弹簧直接载荷式结构,进口压力达到整定值即克服弹簧力开启,过压介质经泄放口排出;压力回落后阀瓣自动回座关闭,最大限度减少冷却液损失。整定压力按订单出厂标定并铅封,现场免调试;阀体铸出流向箭头与整定参数,安装核对直观,广泛用于 CDU 主回路、泵出口与冷板入口保护。
Dead-headed pumps, fouled exchangers or closed valves can push loop pressure past the limits of cold plates and piping, causing leaks. The safety relief valve is the last line of defense: a direct spring-loaded design opens at set pressure, vents the excess through the outlet, and reseats when pressure recovers — minimizing coolant loss. Set pressure is factory calibrated and lead-sealed; flow arrow and set value are cast on the body for easy verification in CDU loops, pump outlets and cold-plate inlets.
| 参数 Parameter | 规格 Specification | |
|---|---|---|
| 整定压力 Set Pressure | 0.2 ~ 1.0 MPa 按需整定 | 出厂整定 + 铅封 Factory set & lead sealed |
| 泄放背压 Back Pressure | ≤ 2 bar | 泄放口接常压管路 Discharge to atmospheric line |
| 通径范围 Size Range | DN8 / DN10 / DN15 / DN20 / DN25 | 按所需泄放量选型 Sized per required discharge |
| 工作温度 Temperature Range | -10 ℃ ~ +120 ℃ | 乙二醇回路适用 Glycol loops suitable |
| 适用介质 Media | 去离子水 / 乙二醇水溶液 | — |
| 启闭特性 Action | 超压开启,回落自动关闭 | 回座压差约 10~20% Reseat 10~20% below set |
| 保护工况 Duty | 整定建议 Setting Tip | |
|---|---|---|
| CDU 主回路 CDU main loop | 整定为系统最高工作压力的 1.1 倍 | 留出裕量,避免频繁起跳 Avoid nuisance lifting |
| 泵出口保护 Pump outlet | 整定低于管路中最弱部件耐压 | 憋压工况优先保护 Protects the weakest component |
| 冷板入口 Cold-plate inlet | 按冷板允许工作压力整定 | 保护微通道结构 Protects microchannels |
| 部件 Part | 材质 Material | |
|---|---|---|
| 阀体 Body | 黄铜 / CF8M 316L(可选) | 黄铜经济型,316L 耐蚀型 Two grades for budget or corrosion duty |
| 阀瓣与阀座 Disc & Seat | 不锈钢精密配研 | 密封可靠,回座严密 Lapped stainless for tight reseat |
| 弹簧 Spring | 不锈钢压力级弹簧 | 整定精度高,抗疲劳 Precise, fatigue-resistant |
| 密封 Seals | PTFE / FKM | 按介质与温度选择 Selected per coolant & temperature |
| 调节螺帽 Adjuster | 铅封防误调结构 | 整定后锁定,防擅改 Locked by lead seal after setting |
| DN8 / DN10 | G1/4 / G1/2 内螺纹 Female thread | 侧向 / 底部泄放口 |
| DN15 ~ DN25 | G1/2 / G3/4 内螺纹 Female thread | 侧向泄放口,可接管引排 |
CDU 主回路超压保护 CDU Loop Protection 板换堵塞或阀门误关时的系统级保护。 System-level protection against blockage or misoperation. | 泵出口憋压保护 Pump Dead-head Protection 泵憋压工况泄放,防止管路与密封超压。 Relieves dead-head pressure on pump and seals. |
冷板与换热器保护 Cold-plate Protection 按冷板耐压整定,守住微通道承压极限。 Set within cold-plate pressure rating. | 储能液冷包 ESS Cooling Loop 电池液冷回路的超压安全冗余。 Overpressure redundancy for battery loops. |
1. 立式安装于被保护设备的上游,按阀体箭头方向接入主管路;
2. 泄放口必须接管引至接液盘或回液箱,严禁直排机房地面;
3. 泄压阀与被保护设备之间不得加装任何隔离阀(或采用联锁双阀组);
4. 定期手柄提动试验,确认阀瓣无粘滞;
5. 铅封与整定螺帽不得擅自调整,变更整定值须返厂标定。
1. Mount vertically upstream of the protected equipment, following the flow arrow. 2. Always pipe the discharge to a drain tray or return tank — never onto the floor. 3. No isolating valve between valve and protected equipment (or use a changeover twin arrangement). 4. Lift the test lever periodically to confirm free movement. 5. Never alter the lead seal; re-set pressure only at the factory.
订货时请注明:整定压力(MPa)· 通径规格(DN8 ~ DN25)· 阀体材质(黄铜 / 316L)· 螺纹标准(G / NPT)· 泄放口形式与背压工况。可按项目需求提供批量配套与出厂测试报告。
When ordering, please specify: set pressure (MPa), size (DN8~DN25), body material (brass / 316L), thread standard (G / NPT), discharge port type and back-pressure. Bulk supply with factory test reports available.
上一页
OCP互锁快断阀
下一页




津公网安备 12011602000999号